As an Amazon Associate I earn from qualifying purchases.
1. DEWALT #ad
DEWALT Dado Throatplate for 10-Inch Portable Table Saw DWE7402DI #adDEWALT #ad
- Package weight: 0372 kilograms. Allows for use of stacked dado cutters. Can be used with dwe7490 and DWE7491 versions. For woodworking and building.
2. Splash Carpentry #ad
Zero Clearance Table Saw Insert for DEWALT Set of 5 #adSplash Carpentry #ad
- Fits models 744, 7480, 745, 7491, 7491rs. Dewalt table saw zero clearance insert plate. Do not purchase for dw7485, we have a different listing for that model.
3. Peachtree Woodworking Supply #ad
Phenolic Zero Clearance Insert for Delta Uni-Saw Contractor | Large Grizzly and Other Table Saws with a 13-3/8” x 3-3/4” x 1/2” Throat Plate Opening #adPeachtree Woodworking Supply #ad
- This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. Zero clearance inserts are table saw specific. Without a zero clearance, the wood has no support by the blade to prevent the wood from tearing out. Measure your factory insert and compare size before you order.
Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert. If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate opening.
Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening. This zero clearance insert is made from a high density phenolic material that was chosen for its ability to stand up to everyday workshop use.
Zero clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. This is especially true when cutting plywood. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. The insert features two snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary. You can also use zero clearance inserts with dado blade sets.
4. Leecraft #ad
Leecraft DL-1U Zero Clearance Table Saw Insert for Delta Table Saw Colors may Vary #adLeecraft #ad
- Measures: 13-3/8" x 3-3/4" x 1/2" Please measure before ordering. Elimantes dangerous gap around blade where thin off-cuts can get wedged.
Fits: delta: unisaw & left-tilt unisaw, jet ctas-10, grizzly g1023, 35610, bridgewood bw10ts, 35675, sears craftsman 22104, 35670, steel City 35605, "hybrid" & left-tilt contractor, powermatic 63, 22124, 10" Tilt Arbor Saw, 10" Contractor, 35680, 22114, 35685.
Offers superior rigidity, flatness, durability, and low friction; reduces chip-out and splintering. Includes leveling screws, side and end adjustment screws; rear safety pin; precut blade bottom pocket for fully retracted blades and bevel cuts.
5. DEWALT #ad
DEWALT Miter Saw Stand Wide Roller Work Support Attachment DW7027 #adDEWALT #ad
- Package weight: 2. 495 kilograms. Compatible with dw723, dwx723 and dwx724 miter saw stands. 15-inch wide roller material support supports wide work pieces when adjusting and cutting. Adjustable height from 4-1/4-Inch to 6-Inch to match any miter saw table height.
|Warranty||3 Year Limited|
6. Fulton Woodworking #ad
Fulton Woodworking PW952 Vintage Sears Craftsman Phenolic Zero Clearance Table Saw Insert #adFulton Woodworking #ad
- The vintage craftsman insert is blank so you can custom fit the blade slot by passing your blade through it. Please check the length, Width and Thickness of your insert before ordering.
Helps to prevent tear out made from high-density phenolic laminate with a bonded-melamine surface. 14 3/8" x 3 3/4" x 3/32" thick. Includes side and end adjustment screws; pre-cut blade bottom pocket.
7. DEWALT #ad
DEWALT Dado Throat Plate DW7444 #adDEWALT #ad
- Use with dewalt 10" Portable Table Saw. Dewalt replacement parts are built with quality and are very durable. Allows for use of stacked dado cutters.
|Warranty||1 Year Full Warranty|
8. DEWALT #ad
Dewalt 0009900146726-02 Genuine Original Equipment Manufacturer OEM Part #adDEWALT #ad
- Genuine, oem Dewalt Replacement Part. Dewalt replacement plate, kerf, part number 146726-02. Measures approximately 8. 00 x 2. 85 x 060 inches.
Compatible with: 3660 type 1, dw705-220 type 1, dw705 type 2, dw703-b3 type 3, dw703 type 3, dw705 type 1, dw705 type 3, dw703-b2 type 3, dw705 type 5, dw703-b2 type 2, dw705 type 6, dw705 type 8, dw703-b3 type 2, 3660 type 3, dw705 type 7, dw704 type 2, dw704 type 3, dw705 type 4a, dw703 type 1, dw703-b3 type 1, dw705-220 type 2, dw704 type 1, dw704 type 4A, 3660 type 2, 3680 type 1, 3680 type 3, DW703-BR Type 3, dw705 type 4, 3680 Type 2, dw704 type 5, dw703-b2 type 1, dw704 type 4, DW705-35 T.